How do I choose who a campaign writes to?

Updated 22 November 2026

The Short Answer

Open the campaign's panel and, on Set Up, press Who It Goes Through. Tick anyone it should reach under Individuals, Groups, Ads or Listings; a tick means they get it. Open a group with its arrow and untick someone to pause them. Groups, ads and listings stay up to date; people ticked by hand stay fixed.

Tick everyone you mean, in as many groups, ads and listings as you like; the line at the foot tells you how many people that is before anything runs.

Where do I set who it goes to?

  1. Open Campaigns and press the campaign's card.
  2. In the panel beside the cards, open Set Up. The first field, Who It Goes Through, shows what it goes to as chips — Buyers, Investors, a person's name — and Change.
  3. Press it. Who It Goes Through opens over the page.
  4. Tick and untick, then press Ok. Cancel keeps it as it was.

The campaign's card has two shortcuts. + Add People at its foot opens the same picker, and Ok saves it the same way. And each row under Who It Goes Through has a ⋯, or a right-click: Pause · Remove on a person, Remove on a group, ad, listing or ad campaign, and Resume on someone under Paused. Everyone and New Leads have no ⋯, and the only row's Remove is grey: a campaign always goes to someone.

There is one Who per campaign; it covers every step. The editor — Edit on the panel, New Campaign, or a card on Browse — shows the same chips and Change under Who on its top box, and opens the same picker; there, your picks are saved with the editor's own button. To add one person from wherever you see them, right-click them and choose Add to Campaign ▸ — see Add someone to a campaign. If your access to Campaigns is less than Full Access, it is grey.

What can I pick?

Four pills sit along the top, with one Search under them:

  • Groups — Everyone and New Leads first, then Your Groups, each with how many people it holds: 51 people.
  • Ads — Your Ads: each of your Meta ad campaigns, with how many ads it holds — Ad Campaign · 3 ads. Ticking one means everyone its ads brought, now and later. Its arrow opens its single ads, each with its kind and head count, such as Lead form · 3 people or Click to Message · 4 people; a single ad is ticked through its ad campaign, not on its own. An ad with no name reads Unnamed Ad.
  • Listings — Your Listings, then Taken Down, each with its price, its site and how many enquired: $1.68M · PropertyGuru · 3 enquired. Ticking one means everyone who enquired about it.
  • Individuals — everyone in your book, with their groups under their name (or No group). A tick means they get it, however they got in.

Tick as many groups, ads, listings and people as you like; someone in two of them gets each message once. Everyone stands alone: ticking it ticks every group. A bar above each list reads Select all 16 — the number is what the list shows, so during a search it takes only the matches. Once some are ticked it reads 2 Selected · Select all 16 · ✕ Clear, and with all ticked 16 Selected · ✕ Clear.

Ticking New Leads greys Groups, and ticks every ad campaign and listing under Ads and Listings: untick any to leave the new leads it brings out — see Leave an ad or a listing out of New Leads. You can still tick people under Individuals; they go through it as if they had just come in.

New Leads is each new lead as they come in: someone new who writes to you first and is your client — on WhatsApp, Messenger, Instagram or email, through your Meta lead form, after tapping your ad, as a portal enquiry, or by leaving their details with your assistant — and isn't already in Prospects or your saved contacts. People you import or add yourself don't count, and nor do the people PropKaki adds to Prospects overnight from your chats.

How do I pause someone?

  1. Press the arrow beside a group, ad or listing. It opens to its people, each ticked.
  2. Untick the person. They stay in the list, unticked and tagged Paused, and the group reads 50 of 51 · 1 paused.
  3. Press Ok.

You can untick them under Individuals too. Someone paused stays out even if they are also in another group, ad or listing you ticked. Tick them again to put them back.

The foot of the picker counts both: 84 people · 1 paused. Back on Set Up, the field names them: Paused: Grace Tan, up to three names and then and 2 more. Pause in This Campaign on a row of the Upcoming tab does the same in one press, and so does Pause on the ⋯ of someone's own row on the campaign's card. Either way they show under Paused on the card, where Resume on their row puts them back.

What happens when people join or leave?

Groups, ads and listings are live. Someone you add to a ticked group, a new lead from a ticked ad, or a new enquiry on a ticked listing joins at the campaign's next run. People ticked by hand under Individuals are fixed: just them.

Someone who is no longer in it gets no further step — whether they left the group, you paused them, or you unticked them. Their messages so far stay on the Sent and Replies tabs. A New Leads campaign is the exception: a lead it has started carries on unless you pause them. On any campaign, their reply stops it for them too, unless Stop sending once reply received is switched off on the editor's last box.

If the campaign was running, a change to Who It Goes Through switches it off; turn it on again and the turn-on check runs for the new audience. Three changes keep it running: pausing a person or leaving an ad campaign or listing out of New Leads; unticking a group; and adding: ticking someone under Individuals, ticking a group under Groups, or ticking back someone you paused or something you left out. Remove on a row of its card is a change like any other: an ad or listing switches a running campaign off, while a group or a person you ticked by hand keeps it on.

How many people is that?

The line under Who It Goes Through on Set Up is the same count the run itself uses: Nobody yet, 1 person, or the number of people. Nobody yet is not an error — an empty group fills in as you add people to it. A New Leads campaign shows no count, because nobody is in it until they arrive; the picker's foot says New Leads · every new lead, as they come in, or New Leads · every new lead, but 1 left out.

The turn-on check goes one step further. It shows which channel is first to reach each person, then ends with a line such as:

  • Nobody is left out — 12 of 12 are reachable.
  • 3 of the 12 can’t be reached at all — no number and no email.
  • Nobody in this list can be reached — no number and no email on file for any of them.

What about a ready-made campaign from Browse?

Every card on Browse arrives with nobody picked: its top box reads Choose Who. The heading it sits under, such as Campaigns for Dormant Leads, and the chips under Who It Suits on its card say who it suits best; they do not pick them for you.

Press the card — or choose Add People from its ⋯, which opens the same editor — then click the top box, set Who, and press Use This Campaign. Press it with Who still empty and the editor stops with Pick who it’s for. and opens that box — your other changes stay as they were.

How do I know it worked?

Turn the campaign on from its switch or Turn It On. The check that opens reads It goes through followed by the audience you picked. If nobody is in it right now, it adds This names nobody right now. and the reason.

Press Turn On or Turn On Anyway and its switch comes on, a Next line under its schedule on its card says when it next starts people, and on Send Automatically its card carries an amber Sends Itself chip.

Still Stuck?

Ask PropKaki in the chat — it answers most of these directly — or message the team.